top of page

How to Reduce P and B Plosive Pops in a Voiceover

Oct 23
4 min read

Updated: Nov 5

A plosive is a breath-driven thump often heard on P or B sounds in a microphone recording. To reduce it, isolate the affected syllable, make a small local correction and compare it with the untouched voice. Do not remove every P sound or apply aggressive bass filtering to an entire narration automatically. If the burst has overloaded the recording, rerecording the phrase may be cleaner than repair.


Distinguish a plosive from other “pops”


Listen to the word and its surroundings. A low thud attached to a breathy consonant suggests a plosive. A very short tick exactly at an edit boundary may be a discontinuity. Crackling on a loud vowel may be clipping. Harsh S sounds occupy another problem category. These can need different treatments, even when listeners call all of them “pops.”


Compare the original file with the edited project and final export. If the defect appears only after an edit, examine that boundary first. If it is already in the source, a later volume change will not undo the original damage. A waveform can help locate the event, but listening determines whether the word remains intelligible.


1. Work on a copy and isolate the event


Save the untouched file. Zoom into the affected word while retaining enough context to hear its meaning. Mark the burst and a small region around it rather than selecting the whole sentence immediately. Preview the passage before changing anything so you know what the repair must preserve.


Start with a modest local level reduction or volume envelope over the thump, with smooth transitions. Compare the entire word, not only the noise in isolation. Reducing the event to silence can delete the consonant and make “pack” sound incomplete. Keep enough articulation for the listener to understand it.


2. Use filtering selectively


A high-pass filter attenuates low frequencies. Audacity documents cutoff and roll-off controls; these should be adjusted by listening to the actual voice. Apply a trial to the small affected region and compare it with the original. A higher cutoff or stronger slope is not automatically a better repair.


For an illustrative edit, suppose the thump occupies roughly 0.08 seconds inside a 20-second sentence. Processing those 0.08 seconds is about 0.4% of that sentence's duration. The point is to minimize unnecessary treatment, not to prescribe a universal selection length. Extend the repair only if the audible problem requires it.


If the treatment leaves a sudden tonal change, smooth the boundaries or use a gentler adjustment. Undo it if the voice loses body or the consonant becomes dull. Do not keep stacking filters simply because a waveform still looks large.


How to fix a plosive pop in one word

Isolate the short burst before the vowel and reduce its low-frequency energy locally. Compare with the original at the same listening level and confirm that the opening consonant remains intelligible.

Process the pop without changing the next vowel

Isolate the burst at the start of one word and try a local reduction or filter on a copy. Compare the same word in the sentence afterward. If the word sounds thinner or harder to understand, shorten the edit region before increasing the effect.

3. Know when replacement is preferable


A severe burst can obscure the actual speech or overload the microphone chain. No filter can guarantee recovery of missing articulation. If you control the recording, capture the phrase again with similar delivery and room sound, then choose a natural edit point. A different take is often less distracting than a heavily processed word.


For synthetic speech, there was no physical microphone breath hitting a diaphragm. A similar thump can still be audible, but diagnose the waveform and playback chain rather than assuming microphone technique explains its cause. Use a suitable existing take or external repair where appropriate; do not promise that spelling changes will cure every artifact.


Prevent plosives in a new recording


Use appropriate microphone placement and a pop filter, as described in Shure's recording guidance. Avoid directing the strongest breath blast straight into the capsule. Keep a consistent position and listen to a short recording containing the troublesome words before recording the full script. A pop filter does not replace sensible levels or a clean recording environment.


Final listening check


Compare repaired and original versions at a similar listening level. Hear the word in its full sentence, on headphones and a small speaker. Check for a missing consonant, a low-frequency jump or an obvious edit. Export once from the best available source and keep the editable project if further revision is needed.


FAQ


Should I use a de-esser for P and B thumps?


A de-esser mainly targets sibilance. A low breath burst usually needs a different diagnosis and treatment.


Will lowering the whole track remove a plosive?


It lowers the speech too. The relative problem remains, so local treatment or replacement is usually more useful.


Is every pop repairable?


No. If the event masks or damages the word, a clean replacement may be necessary. Judge intelligibility and naturalness, not just reduced noise.


If you choose a new narration track


If a damaged word cannot be repaired and you choose a new synthetic recording, prepare the approved wording and pronunciation notes. Our voice workspace creates a separate narration track from text; it does not remove plosive bursts from an uploaded file or guarantee a match to the original voice. Review the new track for artifacts before using it. Create a new narration track only after checking the approved text, available voice samples and displayed total. Samples are not previews of your script. Editing the replacement into a project remains an external task.


Related guides





Sources and scope


Technical documentation checked October 23, 2026. The worked examples are illustrative planning examples, not measured results or product tests.


Shure: microphone techniques for recording


Audacity: High-Pass Filter


bottom of page